Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring PointsVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring Points

How to tell in three seconds whether a hole meets the H7 tolerance

Published 16 October 2026 at 04:17

It is late in the shift and twenty drilled and reamed holes remain to be checked. The vernier caliper reads 44.01 on one hole and 44.02 on the next, but nobody knows for sure whether that is down to the hole, the operator’s hand or how hard the caliper was pressed against the surface. When the question is really just whether the hole is within tolerance, a reading to the hundredth of a millimetre is more information than you need, and at the same time a greater uncertainty than you want.

H7 plug gauge in hardened steel, 44 mm, Go and NoGo on one handle, with serial number, including wear allowance on the Go side, according to DIN 7162/7164, delivered in a plastic tube with the manufacturer's inspection report

A gauge with two ends

A plug gauge is a limit gauge for holes. This one is made of hardened and ground steel for tolerance class H7 and complies with DIN 7162 and 7164. The Go side and the NoGo side are on the same handle. The Go side should slide into the hole without force. The NoGo side should not go in. If it does both, the hole is within tolerance, and for a 44 mm hole H7 means a tolerance zone of 0 to +25 µm. The gauge has a serial number and is delivered in a plastic tube together with the manufacturer’s inspection report, which makes it traceable in the quality system.

Which problems it solves

The decision is the same regardless of who does the measuring. There is no scale to misread and no measuring force affecting the result. The gauge is also faster than a set two-point instrument, and it requires no zeroing before each measurement. The Go side also has a built-in wear allowance, so it can continue to be used for checking over a longer period before it falls outside its tolerance.

Three situations where it is used

In the machine shop, holes are checked right at the machine after drilling or reaming. The operator sees immediately whether the tool has started to wear and can correct it before an entire batch becomes scrap.

In the incoming inspection of purchased parts, such as bearing seats in housings and flanges, it is often enough to know whether the fit works. The plug gauge gives that answer in a few seconds per part, without anyone having to write down measured values.

In maintenance and fixture building, it is used to verify bores in jigs and to decide whether a worn seat can still be used or must be machined again.

Limitations and economics

A plug gauge does not give a measured value. If you need to know how much a hole deviates, or whether it is tapered or oval, a three-point micrometer is the right tool. But for ongoing checks against a known tolerance, the plug gauge is hard to beat. It costs a fraction of a digital instrument, withstands a workshop environment and only requires periodic checking of wear against the inspection report. The gain lies in time per check and in fewer faulty parts moving on in the flow. A single avoided rework or complaint often outweighs the cost of the gauge.

If you have holes with an H7 tolerance that are checked daily, a plug gauge is a simple improvement to the routine. See the plug gauge and the inspection report here.

Read more

More news

All news