Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the naked eye isn’t enough: measure and document the defect directly in the image instead of guessingMoisture is rarely where you can see it: how to tell whether wood, plasterboard and concrete are dry enoughThe cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the naked eye isn’t enough: measure and document the defect directly in the image instead of guessingMoisture is rarely where you can see it: how to tell whether wood, plasterboard and concrete are dry enoughThe cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do not

Why Bore Measurements Show Different Values Depending on Who Holds the Instrument

Published 15 November 2026 at 13:08

Two people measure the same cylinder bore, each with their own inside micrometer, and get different values. The difference is not large, perhaps a few hundredths of a millimeter, but it is enough for a part to be approved on one shift and rejected on the next. The cause is usually not the instrument but how it is held: a slight tilt or a measurement taken just off the diameter gives an incorrect reading.

Digital inside three-point micrometer, Holtest type. Measuring range Ø200–300 mm. Max measuring depth 1100 mm with extension. Resolution 0.001 mm. mm/inch, ABS/INC, automatic shut-off, reset/preset. Self-centering. Carbide measuring faces. IP54. Supplied in an aluminum case with 150 mm extension. Battery V357.

What the Instrument Is

This is a digital inside three-point micrometer of the Holtest type for bore diameters between Ø200 and 300 mm. Three carbide measuring faces are positioned 120° apart and center the instrument by themselves when it is inserted into the bore. The resolution is 0.001 mm and the accuracy is ±0.007 mm. With the included 150 mm extension, a measuring depth of up to 1100 mm can be reached. The display can switch between mm and inches and between ABS and INC, and it has reset and preset functions as well as automatic shut-off. The enclosure is rated IP54, and the instrument is supplied in an aluminum case with a battery of type V357.

What Problems It Solves

With three contact points resting against the bore at the same time, the biggest source of error in two-point measurement disappears: the instrument sitting at an angle or not measuring across the true diameter. The operator’s skill matters less, and the reading is the same no matter who measures. Because the three-point principle also detects out-of-roundness, it becomes easier to see whether a bore is truly round or merely has the correct mean size. The digital readout removes the risk of misreading a scale, and zeroing against a setting ring takes only a few seconds.

When and Why It Is Used

The instrument is used when tolerances are tight and the bores are so large that ordinary hand instruments become unwieldy or unreliable. You zero it against a setting ring of the nominal diameter, insert the measuring head, and take the reading. Measure at several depths to map taper and out-of-roundness.

Three Use Cases

In machine shops, bearing housings and machined housings are checked right at the machine, before the part is unclamped. Errors are then found while they can still be corrected.

When accepting hydraulic cylinders, the bore is measured at several depths using the extension. Wear and irregularities that a single measurement would miss become visible.

In maintenance and engine reconditioning, cylinders in engines and compressors are measured to decide whether they should be honed or replaced. The decision then rests on a measured value and not on a feeling.

The Economics

The instrument is a larger investment than a simple bore gauge. If you count scrap, rework, and discussions about which measured value applies, it still pays for itself quickly, especially when the parts are expensive or the customer requires documented measurements. Less time is spent on repeated measurements, and with proper calibration the results can be traced. A single avoided scrap of a large cylinder or housing can cover a significant part of the purchase.

If you need to measure large bores with repeatable results, this three-point micrometer is an instrument that removes much of the uncertainty that otherwise comes with the hand.

Read more

More news

All news