Hoppa till innehåll
Free shipping over 5.552 SEK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring PointsVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring Points

The Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring Points

Published 15 October 2026 at 05:03

A hydraulic cylinder passes inspection, but the piston still binds or leaks during assembly. The hole was measured to the correct size, but it was measured in a way that doesn’t reveal form errors. A two-point instrument can show the nominal size in one direction and miss that the hole is oval or has three lobes, which can occur with centerless grinding, for example. The result also depends on how the operator holds and angles the instrument.

Digital internal three-point micrometer, Holtest type, IP65. Measuring range Ø12–16 mm. Resolution 0.001 mm. mm/inch, ABS/INC, automatic shut-off, reset/preset. Self-centering. Carbide measuring surfaces. Full measuring range without changing measuring pins. IP65. Battery V357 or CR2032. Supplied in an aluminum case.

What the instrument is

This is a digital internal three-point micrometer for holes between Ø12 and Ø16 mm. Three carbide measuring surfaces are placed at 120° intervals around the axis and center the instrument in the hole by themselves. The resolution is 0.001 mm and the accuracy is ±0.004 mm. The entire measuring range is covered without changing measuring pins. The instrument has IP65 protection, ABS/INC mode, reset and preset, mm/inch switching and automatic shut-off. It is supplied in an aluminum case.

What problems it solves

The self-centering geometry removes a major source of error: the operator’s feel for where the diameter lies. The instrument cannot tilt or end up skewed in the hole the way a two-point tool can. This makes the measurement repeatable between different people and shifts. Since there is no need to change measuring pins within the range, the errors that arise from pin changes and resetting also disappear.

When and how it is used

The instrument is zeroed against a setting ring of nominal diameter. The measuring head is then inserted into the hole until all three measuring surfaces make contact, and the diameter is read off. By measuring at several depths along the hole, you can see whether it is tapered or becomes barrel-shaped or hourglass-shaped. If you also measure at several angles, the ovality becomes apparent.

Three practical applications

In the engineering industry, the instrument is used for acceptance inspection of hydraulic cylinders and machined housings, where the fit against the piston or bearing is critical. In engine and compressor building, cylinder bores and sleeves are checked before assembly, and wear can be tracked over time through repeated measurements at the same depth. In calibration laboratories and quality departments, it is used where two-point measurement is not sufficient as a basis, for example when the form deviation needs to be documented together with the size. The IP65 protection means it can withstand coolant and oil at the machine.

Why it pays off

The cost of a misjudged hole is seldom the measurement itself but what follows: rework, scrapped parts or complaints when a component is already installed in a finished unit. An instrument that shows the correct diameter and at the same time reveals form errors early means problems are discovered at the machine and not at final assembly. The digital readout also reduces the risk of misreading and saves time on production runs, since there is no need to change pins and reset.

If you work with precision holes in the Ø12–16 mm range and want measurement values that don’t depend on who is holding the instrument, a three-point micrometer is a natural step. See specifications and price on the product page.

Read more

More news

All news