Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring PointsVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring Points

The profile projector doesn’t measure the part, but its shadow—reaching where no probe can

Published 23 August 2026 at 19:47

There are components that simply cannot be measured with contact. A thread with a sharp crest, a radius at the bottom of a groove, a thin stamped spring that flexes under the measuring force, an O-ring groove profile that must be accurate across its entire contour and not just in a single dimension. Every probe tip applied either displaces the workpiece or misses the exact point you need to reach.

The profile projector solves this by not touching the component at all. It measures the shadow.

Mitutoyo profilprojektor PJ-P2010A med roterbar skaerm och digital vinkelmaetare

What it is

The Mitutoyo PJ-P2010A is a benchtop profile projector from the PJ-Plus series — the wider sibling to the PJ-P1010A, featuring an extended measuring range along the X-axis.

  • Measuring range 200 x 100 mm, resolution 0.001 mm
  • 10x projection lens
  • Rotatable screen Ø315 mm with digital protractor
  • LED illumination for both surface and contour
  • Measuring stage 380 x 250 mm, maximum workpiece height 90.5 mm
  • Digital XY counters, switchable ABS/INC, RS232C data output
  • Weight 118 kg — requires a stable workbench or a dedicated stand (IEC C13 power cable not included)

The problem it solves

Contour illumination provides a silhouette, surface illumination provides an image — and they answer different questions. With transmitted light from below, the component appears black against a bright background, revealing the exact boundary line of the profile: thread angles, radii, chamfers, and groove shapes. With incident light from above, you instead see the surface — markings, machining marks, and edges that do not extend fully to the outer silhouette. Having both in the same instrument eliminates the need to choose between measuring the geometry and viewing the surface details.

The rotatable screen with a digital protractor is the angle-measuring instrument itself. Instead of calculating an angle from two coordinates, you simply rotate the screen’s crosshairs until they align with the projected edge and take the reading. It functions on the same principle as an optical dividing head, turning angular measurements on a profile into a direct readout rather than a post-process calculation.

The extra X-axis travel is not just a convenience; it eliminates a source of error. A longer turned workpiece — such as a splined shaft, a stud bolt, or a thread on bar stock — that exceeds the measuring range must be reclamped midway, and every reclamping introduces a new zero-point error. With 200 mm of X-travel, the entire component can be measured in a single setup, ensuring all dimensions share the exact same reference.

0.001 mm is the counter resolution, not the measurement uncertainty. The true limit is determined by the edge sharpness on the screen, the perpendicular alignment of the part to the optics, and the operator’s judgment of the edge transition. That is why the illumination and a stable setup matter more to the end result than the final decimal place on the display — and why the 118 kg mass is a functional feature rather than a logistical hurdle.

Three typical use cases

  • Machining: inspection of thread profiles, radii, chamfers, and grooves on turned and milled parts.
  • Stamping and forming: thin, flexible parts that deform under measuring force and cannot be measured via tactile methods.
  • Incoming inspection and dispute resolution: documented verification of purchased components, outputting measurement data via RS232C directly into reports.

Why it pays off

The components that are most difficult to measure are often also the most expensive to scrap and rework: threads, sealing grooves, and stamped springs where the overall geometry — rather than a single linear dimension — determines functionality. When this inspection cannot be performed on the shop floor, the alternatives are either sending samples out for external testing and waiting, or approving parts based on an incomplete measurement that fails to capture the full contour.

A profile projector brings that evaluation directly to the workbench, turning it into something that can be seen, measured, and recorded. And because the measurement is non-contact, the same component can be checked repeatedly without wear or distortion — including parts that are too soft, too small, or too delicate to withstand touch.

Read more about the Mitutoyo profile projector PJ-P2010A →

More news

All news