Hoppa till innehåll
Free shipping over 5.552 SEK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%A core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring PointsWhy the Multimeter Shows the Wrong Voltage on a Variable Frequency Drive and How True RMS Fixes ItMotion blur hides the defect: how strobe lighting freezes a fast-moving detail in the microscope imageVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%A core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsTwo-point measurement in an oval hole gives the wrong diameter, three measuring points do notHow to tell in three seconds whether a hole meets the H7 toleranceThe Hole Measures Right in One Direction but Is Still Wrong: Why You Need Three Measuring PointsWhy the Multimeter Shows the Wrong Voltage on a Variable Frequency Drive and How True RMS Fixes ItMotion blur hides the defect: how strobe lighting freezes a fast-moving detail in the microscope image

A soft material has no thickness until someone defines how hard to press

Published August 25, 2026 at 02:14

Measure a rubber sheet with a micrometer and tighten it until you feel resistance. Then measure again and tighten it a bit more. The reading becomes smaller. Keep going, and it will continue to decrease. The material hasn’t changed — the question was flawed from the start.

Because for anything that yields under pressure, there is no single thickness. There is only a thickness at a given pressure, which is why a measurement of soft materials must always come with a definition of how the measurement was made.

Tjockleksmaetare 0-30 mm med staed typ C foer mjukt gummi och 50 mm halsdjup

What It Is

A thickness gauge with interchangeable anvils, designed for soft materials.

  • Measuring range 0 to 30 mm, graduation 0.1 mm
  • Type C anvil — ø25 mm, designed for soft rubber
  • Hardened steel anvils, hardened and ground reference surfaces
  • Throat depth 50 mm
  • Other anvil types available upon request

The Anvil Type Is the Measurement Definition

The 25 mm diameter is the entire point of Type C. The force applied by the instrument is distributed across that entire surface area, and since pressure is force per unit area, the pressure remains low. A small, hard point with the same force would instead sink into the rubber and measure something entirely different — essentially how deep the tip manages to penetrate.

That is why thickness gauges feature an anvil system instead of a fixed measuring face. Type C with its large contact face belongs to soft rubber; narrower and flat designs belong to paper, cardboard, and fiberboard, which are stiffer and measured across a smaller surface area. Choosing an anvil is therefore choosing which measurement you are actually performing — and two values from different anvil types are not comparable, no matter how accurate they are individually.

The material creeps under the load. Rubber or foam continues to compress as long as the anvil rests against it, quickly at first and then increasingly slower. The reading must therefore be taken at a specific point in time after the anvil makes contact — and at the same point in time every single time. That consistency in habit is often more important for comparability than the instrument’s accuracy.

The 0.1 mm graduation is adapted to reality, not compromised. Soft materials naturally vary more than that between two points on the same sheet. A finer scale would have provided more digits but no additional information, and would primarily invite misinterpreting variations that simply depend on where on the sheet you happened to measure.

The 50 mm throat depth determines where you can reach. A sample often needs to be measured some distance away from the edge, since the edge is where the material is most affected by cutting or punching. The throat depth defines the limit of how far in the instrument can reach, making it the specification to verify against your own sampling routine before buying.

Three Typical Use Cases

  • Rubber and polymers: Thickness of sheets, gaskets, mats, and injection-molded parts.
  • Textiles and leather: Material inspection where pressure and contact area must remain consistent between measurements.
  • Incoming goods inspection: Verifying incoming materials against supplier specifications, using the exact same method as the supplier.

Why It Pays Off

Disputes over material thickness almost never end with someone having measured incorrectly. They end with two parties having measured differently — using different anvils, different contact forces, or different dwell times — and therefore arriving at two figures that are both technically correct. The discussion is then really about methodology, yet it is argued as if it were about the material itself.

An instrument with a defined anvil eliminates that ambiguity. It does not make the measurement itself more accurate, but it makes it comparable, and for incoming materials, comparability is almost always what is truly valuable.

Read more about the thickness gauge with Type C anvil →

More news

All news