Published July 2, 2026 at 13:58
Industrial process control relies on analog signals. A temperature sensor sends 4–20 mA to a PLC. A pressure transmitter sends 0–10 V DC to a variable frequency drive. A level meter sends 4–20 mA to an operator display. When something goes wrong—the sensor shows erratic values, the valve does not move, the alarm is triggered—the first question is always: where is the fault? Is it the sensor, the PLC, or the 500-meter cable between them? Without a tool capable of generating the signal, the only way to answer the question is to swap out components until the problem disappears—an inefficient and often costly method. A handheld loop calibrator provides a diagnosis in minutes.
What a Calibrator Actually Does
The PRC15 calibrator has two primary functions: sourcing precisely known signals (0–24 mA, 0–20 V DC) and measuring the same signal ranges. This combination means you can isolate any component in the signal chain and verify its operation against a known reference.
Used as a source: disconnect the transmitter and connect the calibrator in its place. Set it to 12 mA—midscale. If the PLC displays the expected value (e.g., 50% of the process scale), everything downstream of the sensor is working properly. The problem lies with the sensor. If the PLC displays an incorrect value, the issue is downstream of the calibrator—either in the wiring or the PLC input card.
Used as a meter: let the transmitter output its normal signal and measure it at the other end of the cable. If the reading matches the transmitter’s display, the cable has integrity. If the value differs (e.g., 3 mA instead of 4 mA), the cable has a leakage current or a high-resistance junction degrading the signal.
Practical Features That Count in the Field
Five user-definable presets: Standard test points (4 mA, 8 mA, 12 mA, 16 mA, 20 mA) can be saved to direct-access buttons. During routine calibration of multiple loops, this is the difference between a job taking 10 minutes or 30.
-25% to 125% readout range: Standard 4–20 mA signals can drift outside nominal limits during faults—a drifting transmitter might output 3.2 mA (corresponding to -5% of scale) or 21 mA (corresponding to 106%). The calibrator can both source and measure within this extended range, allowing you to verify complete system behavior—including alarm thresholds.
Large backlit LCD: Easy to read inside dark electrical enclosures, in the shadow behind a controller, or during installation work with only a headlamp. It is a detail that proves essential in real-world conditions.
External power supply (100–240 V universal adapter included): For extended calibration tasks on a workbench or in a lab, the instrument can be powered continuously without draining the batteries. In the field, it is powered by six AA batteries, backed by an extra battery bank for long operating cycles.
Rugged housing: Built for industrial environments—impact-resistant plastic, protective rubber overmolding, and a hard case for transport. It effortlessly withstands everyday handling in control cabinets, transport in a tool bag, and accidental drops onto concrete floors.
Where the Calibrator Proves Its Value
Process industry – instrumentation maintenance: Maintenance and calibration of transmitters for temperature, pressure, level, and flow. Periodic turnarounds require documented calibration—and a handheld calibrator makes it practical to perform the work on-site rather than removing instruments to send them to a lab.
System commissioning: When commissioning new automation systems, every signal loop must be loop-checked. By injecting a signal with the calibrator, you can verify that the PLC reports the correct value to the SCADA system. Without this tool, commissioning becomes pure guesswork.
HVAC service: Control signals between thermostats, controllers, and actuators typically operate on 0–10 V DC. A calibrator turns diagnosing a faulty valve or a non-responsive actuator into a five-minute task.
Power utilities and energy generation: Monitoring and control signals in substations, generators, and pump stations. The calibrator is used for both routine maintenance and troubleshooting during system disruptions.
Food and beverage manufacturing: Temperature monitoring across cold chains and sterilization processes, pressure monitoring during pasteurization, and flow measurement in CIP (Clean-In-Place) systems. GMP standards require documented calibration of all these critical loops.
Pharmaceutical manufacturing: Qualification and validation activities for process instrumentation. The calibrator is an essential part of the tool set required under PIC/S GMP compliance.
Marine and offshore service: Modern shipboard automation relies on hundreds of 4–20 mA loops. Troubleshooting without proper instrumentation is impossible; a handheld calibrator is a standard fixture in every marine instrument technician’s toolkit.
Technical education: Automation engineering students require hands-on experience with the instruments they will use in the field. A calibrator is an essential training tool for technical colleges and universities.
What the Kit Includes
The PRC15 calibrator, test leads with alligator clips, a 100–240 V AC universal power adapter with four plug types (EU/UK/US/AU), six AA batteries, and a rugged hard carrying case.
Return on Investment
Priced at 7,681 SEK, this instrument quickly pays for itself through more efficient troubleshooting. A single field service call where downtime and diagnostic time are cut from hours to minutes covers a significant portion of the cost. For automation consultants, this is often the specific tool that clients look for—making the distinction between a true professional and someone relying on trial and error.
Read more: PRC15 Voltage and Current Calibrator in the store →