Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%A Bore That Is Right at the Opening Can Be Wrong 400 mm Further InWhen the naked eye isn’t enough: measure and document the defect directly in the image instead of guessingMoisture is rarely where you can see it: how to tell whether wood, plasterboard and concrete are dry enoughThe cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holdsVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%A Bore That Is Right at the Opening Can Be Wrong 400 mm Further InWhen the naked eye isn’t enough: measure and document the defect directly in the image instead of guessingMoisture is rarely where you can see it: how to tell whether wood, plasterboard and concrete are dry enoughThe cold room was too warm last night, but nobody knew when it startedThe Fuse Trips Once a Night: How to Find the Cause with a Logged Load CurveA core temperature reading in 0.4 seconds makes self-inspection a habit instead of an interruptionWhy Bore Measurements Show Different Values Depending on Who Holds the InstrumentThree Seconds at the Core: How to Make Temperature Control in Food Production Both Faster and SaferThe Brix value decides: get a reading in seconds instead of a guess by eyeThree seconds is enough to tell whether the core temperature holds

A Bore That Is Right at the Opening Can Be Wrong 400 mm Further In

Published 21 November 2026 at 00:31

You measure a hydraulic cylinder at the mouth and get a value well within tolerance. Yet the cylinder leaks when it runs in the machine. The wear is rarely located where a standard internal measuring instrument easily reaches. It sits in the middle of the stroke, where the piston works the most, and the measuring head cannot get in there.

Schwenk measuring instrument with analog dial indicator for internal measurement, 18-35 mm, measuring depth 500 mm

What the instrument is

This is a two-point internal measuring instrument from Schwenk with an extended rod for great measuring depths. The measuring range is 18 to 35 mm and the reach is 500 mm. The measuring head sits at the far end of the rod and has two opposing contacts, a fixed reference and a spring-loaded measuring tip. The deviation is transferred to an analog dial indicator at the handle, so you read the value outside the bore.

What problems it solves

A long bore is rarely equally straight and round all the way through. The two-point principle shows diameter variation, ovality, taper and barrel-shaped bulging as deflections of the pointer. This lets you find out what the bore looks like along its entire length, not just a single dimension at the opening.

How it is used

Select a setting ring with the nominal bore diameter and zero the dial indicator with the head in the ring. Then insert the head into the bore and note the pointer deflection at several positions along the length. A few readings at even intervals are enough to see whether the bore is tapered, oval or worn in one spot. The handle is dimensionally stable across temperature, which is important when the instrument is held in the hand for a while.

Three applications

Hydraulics and maintenance. Long cylinders are inspected before refurbishment. The measurement shows whether the cylinder can be honed or whether the tube needs to be replaced.

Conveyors and gearboxes. Long bushings and bearing seats wear unevenly. With an instrument that reaches all the way, wear can be assessed without disassembling more than necessary.

Machine shops and tubing. Deep bores in machine tools and in tubes for oil and gas applications must be approved against the drawing. Here the instrument serves for incoming inspection and final inspection.

Why it pays off

A misjudged bore costs more than a measuring instrument. Either a cylinder that could have been repaired is replaced, or one that is already too worn is installed and has to be taken out again after a few weeks. Downtime on a production line is more expensive than both the cylinder and the instrument. Since the reading is taken on a standard dial indicator, no special equipment is needed, and the operator can learn the method in a short time. Wear parts such as measuring tips can be replaced without the whole instrument needing service.

To the product

If you regularly measure bores that are deeper than a standard instrument can reach, this is a tool that gives you measurements where the errors actually occur. Look at the specification and see whether the measuring range suits your parts.

Read more

More news

All news